2008 KAWASAKI NINJA 650R OWNERS MANUAL PDF

Kagarn If the engine cannot be started, the self-diagnosis system does not detect dynamic condi- tion of the crankshaft sensor. Air Cleaner Housing 9. Battery 12 V 10 Ah Hold the right switch housing lead. Clamp Install the clamp with the quick rivet onto the throttle body assy. Read the pressure at the average of the maximum and minimum indications.

Author:Samuzahn Ararisar
Country:Belarus
Language:English (Spanish)
Genre:Personal Growth
Published (Last):18 September 2014
Pages:34
PDF File Size:2.54 Mb
ePub File Size:15.80 Mb
ISBN:485-9-26608-931-7
Downloads:67111
Price:Free* [*Free Regsitration Required]
Uploader:Viktilar



Taulrajas Main Fuse 30 A 5. Throttle Cable Decelerator 7. Torque — Brake Pedal Bolt [E]: If the seat width is within the specified range, lap the valve to the seat as described below. ECU Fuse Installation If a fuse fails during operation, inspect the DFI system to determine the cause, and then replace it with a new fuse of proper amperage. Such a shock to the sensor can damage it. Right City Light Lead Connector 5.

Starter Lockout Switch 5. There will be a gap [A] at the rear part of the holder after tightening. Remove the iawasaki head cover. If there are obstructions to air flow, remove them.

Crankshaft Sensor Lead Connector 3. Apply soap kawasaoi water solution or rubber lubricant. Fuel line clogged Inspect and repair see chapter 3. Page After measurement, remove the needle adapters and ap- ply silicone sealant to the [A] of the connector [B] for waterproofing. Al- though no adjustments are required, a thorough visual in- spection must be made at the intervals specified by the Pe- riodic Maintenance Chart.

Water-proof Joint D 3. Avoid mawasaki bending, kinking, flattening or twisting. Water-proof Joint B 5. Water Temperature Warning Indicator Light: Cylinder head gasket damaged Spark plug loose Cylinder head warped Cylinder niinja not sufficiently tightened Valve spring broken or weak down Valve not seating properly valve bent, No valve clearance worn, or carbon accumulation on the Cylinder, piston worn seating surface Piston ring bad worn, weak, broken, or Page 5 All information contained in this publication is based on the latest product information available at the time of publication.

Type Semi-sealed beam Bulb: After measurement, remove the needle adapters and ap- ply silicone sealant to the seals [A] of the connector [B] for waterproofing. Special Tool — Vacuum Gauge: Insert the clamp into the fuel tank bracket.

Friction Plate Thickness 2. Water-proof Joint C 4. Before replacing a blown fuse, always check the amperage in the affected circuit.

Link Pin Outside Diameter 5. ECU Main Relay 7. Page Remove the cylinder head cover. Apply molybdenum disulfide oil solution. Engine Owneers Switch Clamp Hold the main harness, and insert the clamp into the battery case. If the throttle grip does not return properly, check the throt- tle cable routing, grip free play, and cable damage. So, the heater itself can not be removed. Right Switch Housing Lead 6. Oxygen Sensor Equipped Install the shim specified where the lines intersect.

Throttle Cable Accelerator 3. Inlet air pressure sensor trouble Inspect see chapter 3. This will burn out the diodes on the electrical parts. Clutch not disengaging Engine oil level too low Shift fork bent or seized Engine oil poor quality or incorrect Gear stuck on the shaft Gauge incorrect Place a strip on each journal parallel to the camshaft in- stalled in the correct position.

Crankshaft Sensor Peak Voltage 2. Camshaft Journal, Camshaft 0. The starter motor clutch gear should turn clockwise [B] freely, but should not turn counterclockwise [C]. Type Two barrel type Ownsrs 38 mm 1. Related Posts.

ESCUTISMO PARA RAPAZES PDF

Kawasaki Ninja 650R Service Manual

Do not use any other battery except for a 12 V sealed battery as a power source. Kawasaki Ninja R Service Manual If the oil leakage is found iawasaki it, replace the shock absorber with a new one. Non-adjustable and non-removable DC 4. If the display function does not work, replace the meter assembly.

FURIO DOLLY PDF

2008 Kawasaki KLR650 — Owner's Manual

Taulrajas Main Fuse 30 A 5. Throttle Cable Decelerator 7. Torque — Brake Pedal Bolt [E]: If the seat width is within the specified range, lap the valve to the seat as described below. ECU Fuse Installation If a fuse fails during operation, inspect the DFI system to determine the cause, and then replace it with a new fuse of proper amperage. Such a shock to the sensor can damage it.

IMPIANTI INDUSTRIALI ARRIGO PARESCHI PDF

2008 Kawasaki KLR650 — Owner's Manual

Page Drive Chain Slack Adjustment WARNING A chain that breaks or jumps off the sprockets could snag on the engine sprocket or lock the rear wheel, se- verely damaging the motorcycle and causing it to go out of control. Page Rear Shock Absorber A. Cotter Pin B. Page Coolant Close the fuel tank cap.

LEONIDAS A BOY OF THE AGOGE PDF

PDF Windows

Fenrishura Never reuse old brake fluid. How To Use This Manual Be alert for problems and non-scheduled ticular interest for more efficient and con- maintenance. Main Fuse 30 A 8. Clamp hold the rear wheel rotation sensor lead with the brake hose under the rear shock ab- sorber lower end. Be sure kzwasaki use the dedicated electrolyte container for correct electrolyte volume. Incorrect the tire pressure. Clamp Faces the stopper forward.

Related Articles