CPSC 16 CFR 1201 PDF

Goltishakar When broken, it will break into many relatively small fragments, which are less likely to cause serious injury. Compliance with a new set of U. To pass this standard, there must be a no fracture, or b if the glass fractures, the ten largest glass particles must weigh no more than 10 square inches of the original glass tested. John Kent, administrator for the Safety Glazing Certification Council SGCCsays every manufacturer or importer of an architectural glazing material that is subject to 16 CFR Part will be required to comply with these new regulations, and this will certainly mean many fabricators will have a lot of questions.

Author:Dogul Guzilkree
Country:Slovenia
Language:English (Spanish)
Genre:Sex
Published (Last):17 May 2010
Pages:270
PDF File Size:9.49 Mb
ePub File Size:4.74 Mb
ISBN:365-4-78378-562-3
Downloads:52130
Price:Free* [*Free Regsitration Required]
Uploader:Tular



Tygosar 16 CFR Under these new regulations, manufacturer certifications of compliance with CPSC 16 CFR the federal safety standard for architectural glazing materials-must include the following: The typical process to produce tempered glass involves heating the glass to over 1, degrees F, then rapidly cooling to lock the glass surfaces in a state of compression and the core in a state of tension.

Some in the industry say these changes are not likely to have a huge impact on the way glass fabricators have already been doing business. Guardian Residential Glass Innovation. All measurements taken from center-of-glass values. Compliance with a new set of U. No reproduction, in print, electronic or any form without the expressed written permission of Key Communications Inc. Guardian Tempered Glass For those companies that buy labeled glass and then have to cut it, the required information will still be available as Kent says it can appear on 1 a paper certificate, 2 the actual product label, or 3 by reference to a website, or some combination of these.

Need more info and analysis about the issues? They then will provide a statement on shipping documents that 1 certified they meet the regulation, addresses the date of manufacture, 3 identified the product, and 4 references a website where remainder of the information may be obtained. Category I is for glass products with an area not greater than 9 square feet and must endure a lb. John Kent, administrator for the Safety Glazing Certification Council SGCCsays every manufacturer or importer of an architectural glazing material that is subject to 16 CFR Part will be required to comply with these new regulations, and this will certainly mean many fabricators will have a lot of questions.

Fully tempered ClimaGuard glass is approximately four to five times stronger than annealed glass of the same thickness and configuration, residual surface compression must be over 10, PSI for 6mm, according to ASTM C Does the glass then need to be labeled? This type of glass is intended for general glazing, and safety glazing such as sliding doors, storm doors, building entrances, bath and shower cpzc, interior partitions, and other uses requiring superior strength and safety properties.

For example, what happens if a fabricator has to remove and reinstall the same piece of glass? Learn About Window Glass. To pass this standard, there must be a no fracture, or b if the glass , the ten largest glass particles must weigh no more than 10 square inches of the original glass tested. Therefore, I see most manufacturers using a hybrid approach with the information being distributed between the permanent logo, the shipping documentation and the fabricators website.

There is too much required information to put it all on the permanent logo on the glass and still have the glass acceptable to owners and architects. Related Posts

BRAINSEX ANNE MOIR & DAVID JESSEL PDF

2406.1.1 Cpsc 16 Cfr 1201

This part , a consumer product safety standard, prescribes the safety requirements for glazing materials used or intended for use in any of the following architectural products: 1 Storm doors or combination doors. It also requires that these architectural products which incorporate glazing materials be constructed with glazing materials that meet the requirements of this part. The safety requirements are designed to reduce or eliminate unreasonable risks of death or serious injury to consumers when glazing material is broken by human contact. The standard applies to glazing materials and architectural products incorporating glazing materials that are produced or distributed for sale to or for the personal use, consumption or enjoyment of consumers in or around a permanent or temporary household or residence or in recreational, school, public, or other buildings or parts thereof. This part applies only to those glazing materials manufactured after the effective date of the standard; and to those architectural products identified in paragraph a of this section that are manufactured after the effective date of the standard. Thus, architectural products identified in paragraph a of this section manufactured after the effective date of the standard must incorporate glazing materials that comply with the standard.

CONTADORES ASSINCRONOS E SINCRONOS PDF

CPSC 16 CFR 1201 PDF

When broken, it will break into many relatively small fragments, which are less likely to cause serious injury. Need more info and analysis about the issues? All measurements taken from center-of-glass values. For example, what happens if a fabricator has to remove and reinstall the same piece of glass? Category I is for glass products with an area not greater than 9 square feet and must endure a lb. Under these new regulations, manufacturer certifications of compliance with CPSC 16 CFR the federal safety standard for architectural glazing materials-must include the following: To pass this standard, there must be ctr no fracture, or b if the glass fractures, the ten largest glass particles must weigh no more than 10 square inches of the original glass tested. This type of glass is intended for general glazing, and safety glazing such as sliding doors, storm doors, building entrances, bath and shower enclosures, interior partitions, and other uses requiring superior strength and safety properties.

IBM 3573-TL PDF

Safety Standard for Architectural Glazing Materials

.

Related Articles